The DHS Program User Forum
Discussions regarding The DHS Program data and results
Home » Topics » Domestic Violence » Multilevel modeling with svy and domestic violence weights (How to best apply level 1 and level 2 weights)
Multilevel modeling with svy and domestic violence weights [message #23647] Tue, 26 October 2021 08:50 Go to next message
hbsheldon is currently offline  hbsheldon
Messages: 2
Registered: July 2021
Member
Hello,

I am working on running a meprobit that looks at the determinants of domestic violence experience at the country-level (for several African countries, but with a regression for each country). I recently used this DHS Methodological Report 27 (https://www.dhsprogram.com/pubs/pdf/MR27/MR27.pdf) to estimate level 1 and level 2 weights for IPV acceptance (which is answered by all women, not just women in the domestic violence module). I am looking for recommendations on how to calculate level 1 and level 2 weights for domestic violence. Repeating the same procedure outlined in MR27 for the domestic violence weight yields weights that are inconsistent between groups for level 2.
1) Some other forums suggested using the geometric mean or a weight = 1 for level 2 weights. Which weight is preferred for level 2?
2) For level 1, would it be ok to use the domestic violence weighted version of the alpha values for level 1, or the domestic violence weight on its own? Based on my research, I am concerned that using the domestic violence weight without any sort of rescaling/manipulation would be incorrect.


Thank you in advance!

[Updated on: Tue, 26 October 2021 13:16]

Report message to a moderator

Re: Multilevel modeling with svy and domestic violence weights [message #23656 is a reply to message #23647] Wed, 27 October 2021 16:56 Go to previous messageGo to next message
Bridgette-DHS is currently offline  Bridgette-DHS
Messages: 2442
Registered: February 2013
Senior Member

Following is a response from DHS Senior Sampling Specialist, Mahmoud Elkasabi:

I would use the same procedures used in MR27 initiated with the DV weight, d005 as [gen DHSwt = d005 / 1000000]. All other steps should remain the same.
Re: Multilevel modeling with svy and domestic violence weights [message #23657 is a reply to message #23656] Wed, 27 October 2021 17:16 Go to previous messageGo to next message
hbsheldon is currently offline  hbsheldon
Messages: 2
Registered: July 2021
Member
Thank you for your response! When I try the same technique as MR27 but only with replacing v005 with d005, I get the following error:
"weights in variable wt2_domv_4 not constant within groups defined by: v001"
where wt2_domv_4 is wt2_4 but for domestic violence.

Here's a comparison of weights by cluster below:

. list	v001	wt2_1 wt1_1	wt2_domv_1	wt1_domv_1	v005_weight domv_weight in 1/50	if	v044	==	1

						
	v001	wt2_1	wt1_1	wt2_do~1	wt1_do~1   v005_w~t   domv_w~t 
					-
2.	1	1.5	8.878671	1.5	6.819981    .118748    .091214 
10.	1	1.5	8.878671	1.5	6.819981    .118748    .091214 
13.	1	1.5	8.878671	1.5	6.819981    .118748    .091214 
14.	1	1.5	8.878671	1.5	15.58844    .118748    .208488 
19.	1	1.5	8.878671	1.5	6.819981    .118748    .091214 

						

[Updated on: Wed, 27 October 2021 17:16]

Report message to a moderator

Re: Multilevel modeling with svy and domestic violence weights [message #23670 is a reply to message #23657] Fri, 29 October 2021 15:42 Go to previous message
Bridgette-DHS is currently offline  Bridgette-DHS
Messages: 2442
Registered: February 2013
Senior Member


Following is another response from DHS Senior Sampling Specialist, Mahmoud Elkasabi:

Yes, this is correct because the DV weight is calculated on the individual level and not on the cluster level as other weights. I would suggest approximating the wt2 using the women weight or the HH weight and then calculating wt1 based on d005 and the approximated wt2. See the Stata code below as an example.
Previous Topic: 2016 disability, partner behaviors, and intimate partner violence report
Goto Forum:
  


Current Time: Wed Dec 1 20:01:55 Coordinated Universal Time 2021